Worldwide Installations

Shreeji Expeller Industries

Facebook Twitter Pinterest

Estd. 1992

Manufacture & Exporter of Oil Mill Machinery & Vegetable Oil Refinery Plant

Shreeji Expeller IndustriesShreeji Expeller Industries

Home » Products » Oil Expeller / Oil Screw Press » Soybean Oil Expeller

Soybean Oil Expeller


  • GearBox : Double reduction Gear box
  • Kettle / Cooker : Multi stage cooker for the conditioning of seeds
  • Chamber :Vertical Hinged and can very easily be opened for replacement of worms or cage bars. This
    saves a lot of time and labour.
  • Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars.
  • Bearings : Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation.
  • Compressing : Crammer Shaft gives extra Cramming of the seed or cake in the Feed
  • Shaft Withdrawal : The main Worm Shaft can be withdrawn very easily without disturbing the gear
    section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The
    thrust of the pressure worms is taken upon large spherical roller thrust bearings.
  • Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds.
  • Reduced internal wear and tear
  • Best Quality of Oil & Cake.
  • Maintenance is less & easy
  • Hardened Worm Assembly
  • Cast Iron Bodies: For perfect alignment and stability.
  • Steel Fabricated Base

Model of Expeller SHREEJI VK-130
Chamber Fabricated chamber
HP 3 Phase 50 HP Motor
Capacity 20 TON / 24 Hour




Screw Oil Press


  • Chambers : Reduces time and labour for relining of Cage Bars
  • The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy.
  • Shaft Withdrawal : The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
  • Gear Box & Lubrication : An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is
    oil tight and dust proof, totally enclosed design and is fitted with level indicator. Aself contained lubrication arrangement has been provided.
  • Kettle / Cooker : Multistage vertical stack cooker for proper conditioning of the seeds.
  • Lower Power Consumption: The Selection of motors is done keeping in mind the peak load that could arise due to inconsistent feeding resulting in lower power consumption.
  • Premium expelled Oil Quality : Well designed worm assembly and chamber construction ensures superior quality of expelled oil.
  • Superior Quality of Cake : The cake quality is excellent and cake produced from the machine is of natural colour without charring or burning effect .
  • Retention of oil in Cake : Superior process parameters ensure accurate retention of oil in the cake.

Model of Expeller SHREEJI VK-130
Chamber Two Chambers
HP 3 Phase 50 HP Motor
Capacity 18 to 21 TON / 24 Hour




Mini Oil Mill


  • Chambers : Reduces time and labour for relining of Cage Bars
  • The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy.
  • Shaft Withdrawal : The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
  • Gear Box & Lubrication : An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is
    oil tight and dust proof, totally enclosed design and is fitted with level indicator. Aself contained lubrication arrangement has been provided.
  • Kettle / Cooker : Multistage vertical stack cooker for proper conditioning of the seeds.
  • Lower Power Consumption: The Selection of motors is done keeping in mind the peak load that could arise due to inconsistent feeding resulting in lower power consumption.
  • Premium expelled Oil Quality : Well designed worm assembly and chamber construction ensures superior quality of expelled oil.
  • Superior Quality of Cake : The cake quality is excellent and cake produced from the machine is of natural colour without charring or burning effect .
  • Retention of oil in Cake : Superior process parameters ensure accurate retention of oil in the cake.


COOKER / COOKING VESSEL :


Brief Outstanding Features
Cookers / Heating Kettles are used for proper heating and conditioning of the oil seeds prior to expelling.Controlled
heat and moisture open up the oil bearing cells for maximum oil yield.

Construction
These Cookers are all steel fabricated with steam heated jackets for each compartment. These jackets are suitably welded with studs and hydraulically tested before assembly. All compartments except the top one are provided with hinged doors for easy access.

Heating
Steam jackets are indirectly heated by steam and cookers are complete with necessary fittings i.e. valves, pressure gauges, relief valves, steam traps and thermometer. Bottom stage insulation of the Cookers avoids unnecessary heat losses. Insulation can be provided at extra cost.

Moisture Addition
Open steam spray is provided for bottom compartment of smaller cookers and for other sizes at the top and bottom compartments.

Control
Seed temperature, retention time in each stage, moisture content and depth are easily controlled.

Drive
The vertical shaft carries biparted agitators for each compartment and is driven from an independent electric motor through V-Belt and vertical cooled worm type speed reduction gear box.

Steam Consumption
Higher figures are for starting up and the lower figures are for steady running.

Dia x Ht.(mm) No. of Compartments Total Heating area in Sq. M Total volume Cu. M. Steam Consump. Kg/hr. Steam Pressure Kg/cm2 Motors main drive H.P. Exhaust FanMotor H.P. Main Drive
1676x2438 5 11.035 6.230 160 8 20 1.5 V. Belt &Gear Box

Model of Expeller SHREEJI VK-130
Chamber Two Chambers
Each of 36" Long
HP 3 Phase 100 HP Motor
Capacity 50 to 60 Ton (In 24 Hours) in pre-pressing
and 25 to 30 Ton in Single & Final crushing




Cottonseed Oil Expeller


  • Steel : Each of 36″ Long Eliminates the difficult task of removing box for replacement of worms.
  • Steel Casted Chambers : Reduces time and labour for relining of Cage Bars The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy.
  • Shaft Withdrawal : The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
  • Gear Box & Lubrication : An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is oil tight and dust proof, totally enclosed design and is fitted with level indicator. A self contained lubrication arrangement has been provided.
  • Kettle / Cooker : Multistage vertical stack cooker for proper conditioning of the seeds.
  • Lower operation and maintenance cost : Due to sturdy construction and stringent quality norms our machines work with higher efficiency and incur lower maintenance costs.
  • Premium expelled oil quality : Well designed worm assembly and chamber construction ensures superior quality of expelled oil.
  • Superior Quality of Cake : The cake quality is excellent and cake produced from the machine is of natural colour without charring or burning effect .
  • Retention of oil in cake : Superior process parameters ensure accurate retention of oil in the cake . Power:The power required is 3-Phase 170 H.P. Motor.
  • Capacity : 140 to 150 Ton (In 24 Hours) in pre-pressing and 50-60 Ton in Single & Final crushing.


COOKER / COOKING VESSEL :


Brief Outstanding Features
Cookers / Heating Kettles are used for proper heating and conditioning of the oil seeds prior to expelling.Controlled
heat and moisture open up the oil bearing cells for maximum oil yield.

Construction
These Cookers are all steel fabricated with steam heated jackets for each compartment. These jackets are suitably welded with studs and hydraulically tested before assembly. All compartments except the top one are provided with hinged doors for easy access.

Heating
Steam jackets are indirectly heated by steam and cookers are complete with necessary fittings i.e. valves, pressure gauges, relief valves, steam traps and thermometer. Bottom stage insulation of the Cookers avoids unnecessary heat losses. Insulation can be provided at extra cost.

Moisture Addition
Open steam spray is provided for bottom compartment of smaller cookers and for other sizes at the top and bottom compartments.

Control
Seed temperature, retention time in each stage, moisture content and depth are easily controlled.

Drive
The vertical shaft carries biparted agitators for each compartment and is driven from an independent electric motor through V-Belt and vertical cooled worm type speed reduction gear box.

Steam Consumption
Higher figures are for starting up and the lower figures are for steady running.

Dia x Ht.(mm) No. of Compartments Total Heating area in Sq. M Total volume Cu. M. Steam Consump. Kg/hr. Steam Pressure Kg/cm2 Motors main drive H.P. Exhaust FanMotor H.P. Main Drive
1676x2438 5 11.035 6.230 160 8 20 1.5 V. Belt &Gear Box





Looking for Product Name ?